Bulk Loading Guns

The first question about bulk loading guns is if they are worth buying. At current retail price levels (2017) if we compare the retail cost of Perma-Chink in pails compared to 30 ounce tubes, the price of two pails is $454.50 while the price of an equivalent amount of Perma-Chink in 30 oz. tubes is $689.00. Rather than buying four cases of 30 oz. tubes you can buy two pails of Perma-Chink and a Cox Bulk Loading Gun and a Follow Plate for $143.35 and still have $91.15 left over. Plus you will have a great tool for future use. In the case of Energy Seal the savings are even greater. Two pails of Energy Seal plus the Bulk Loading Gun and Follow Plate ends up being $146.15 less expensive than four cases of 30 oz. tubes.

So now that we know that they can save you money, how easy are they to use? First of all don’t try to save more money by not buying the Follow Plate. The Follow Plate is an integral part of the Bulk Loading Gun system and trying to load a gun without it can be a very frustrating and messy experience.

Let’s go through the procedure of loading and using a Cox Bulk Loading Gun step by step.

1. Remove the lid and the plastic liner from the pail. Put them aside and try to keep them clean in case you need to reseal the pail later.

2. Place the follow plate on top of the product in the pail making sure that there is a good seal between the wall of the pail and the flexible edges of the follow plate.

3. Remove the cap and cone tip from the end of the Cox gun barrel and ensure that the rod and plunger are fully forward.

4. Push the end of the barrel onto the lip surrounding the hole in the middle of the Follow Plate. Make sure the gun is perpendicular to the plate, and there is a tight seal between the barrel and the O-ring. If the barrel is tilted air will be sucked into the gun during the loading process.

5. Depress the rod release plate and draw back the rod with a smooth, even pull. Make sure the barrel stays flush with the plate and don’t tilt the gun as you pull the rod back.

6. Once the rod is fully extended and the barrel is full of product, give the trigger one squeeze then disengage the barrel from the Follow Plate with a twisting motion.

7. Attach the end cap and cone tip to the end of the barrel. Make sure the tip of the cone is cut to the diameter of the bead you want to apply.

8. Apply sealant using the same technique as you would use with a standard caulk tube and ratchet gun.

9. To remove the Follow Plate from an empty or partially full container, insert the handle rod into the open nut on the surface of the plate and pull it out.

10. Replace plastic liner over the surface of the sealant.

11. Replace the lid. Make sure that it is seated tight on the pail.

Make sure that the plungers are positioned correctly on the end of the rod. If the gun begins to suck air, tighten the blue base with the wrench that comes with the gun.


Step 1


Step 2


Step 4


Step 5


Step 6


Step 7


Step 8


Step 9


Step 10


Step 11

Last modified on Monday, 15 January 2018 21:33

Monthly Special

loyal 0919 cc

Subscribe via Email

Join the Perma-Chink Family!

Receive News and Loyal Customer Offers

On a phone? Text LOGEXPERT to 22828

Project Spotlight

  • A simple comparison of the cost of a gallon of wood stain is a mistake because all stains differ in their lifespan, coverage rate and quality of appearance and protection

    Whether you’re currently building your dream log home or simply checking off tasks on your annual home-maintenance “to do” list, we’re always looking for ways to skimp on expenses around the house.

    But when it comes to putting your best foot forward with a beautifully stained home that’s also protected from the exterior elements, you might want to think twice before being lured in by the lower price tag of a middle-of-the-road finishing product.

    Think about it

  • Lifeline Ultra-7 stands out as THE top-of-the-line, long-lasting finish. Take a look at our tutorial video on proper application technique.

    Project Spotlight